DIY Tub Installation.
DIY Tub Installation.
Blog Article
Everybody maintains their unique piece of advice in relation to How to Install a Bathtub.
Installing a bathtub isn't precisely rocket science, however it does call for strong plumbing, woodworking, and in some cases, tiling abilities. Changing an old bath tub with a new one is also a moderately challenging job. If the old tub is easily available, the job can relocate immediately; if you need to open up a wall to remove the old tub and position the new bathtub, the task is much harder. In either case, the project is within a home handyman's abilities, although you will certainly require an assistant to leave the old bathtub as well as embeded in the new one. Make certain you have actually qualified yourself for the work and also fit trying it. As opposed to employing a specialist to take over a halfway-completed job, it is better to consider using one prior to you start. Possibilities are you may require a specialist plumber to make tube links.
This post will help you install a brand-new bath tub in your shower room if you have currently acquired a brand-new tub and don't require to alter the plan of your previous supply of water pipelines.
Your devices as well as material checklist need to make up the following:
Getting ready for the Installation
To start with, the sustaining framework supplied with the bathroom must be fitted (if needed) according to the manufacturer's guidelines. Next off, fit the taps or mixer to the bath tub. When suitable the tap block, it is important to make certain that if the tap features a plastic washer, it is fitted in between the bathroom as well as the faucets. On a plastic bathroom, it is also practical to fit a supporting plate under the faucets system to prevent pressure on the tub.
Fit the adaptable faucet connectors to the bottom of both taps making use of 2 nuts as well as olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet with the hole in the bath. Make use of the nut provided by the maker to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. Ensure you make use of all of the provided washers.
Link the catch to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Link all-time low of the overflow tube in a similar manner.The bathroom should currently be ready to be suited its final placement.
Removing Old Taps
If you require to replace old faucets with new ones as a part of your installation, after that the first thing you should do is detach the water supply. After doing so, activate the taps to drain pipes any water continuing to be in the system. The process of eliminating the existing faucets can be fairly problematic as a result of the restricted gain access to that is often the situation.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that attaches the supply pipes to the faucets. Have a cloth prepared for the continuing to be water that will certainly come from the pipes. As soon as the supply pipelines have been eliminated, make use of the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary faucets from transforming during this process. When the faucets have actually been removed, the holes in the bath/basin will have to be cleaned up of any type of old securing substance.
Prior to moving on to fit the new taps, compare the pipeline links on the old faucets to the brand-new faucets. If the old taps are longer than the new faucets, after that a shank adapter is needed for the brand-new faucets to fit.
Mounting the Bath tub
Making use of both wood boards under its feet, position the bath tub in the needed setting. The wood boards are practical in uniformly spreading the weight of the bathtub over the area of the boards instead of focusing all the weight onto four tiny factors.
The following objective is to ensure that the bath tub is leveled all round. This can be accomplished by inspecting the spirit level and also readjusting the feet on the tub until the level reviews level.
To install faucets, fit all-time low of the furthest flexible faucet connector to the ideal supply pipeline by making a compression sign up with; then do the same for the various other faucet.
Turn on the water system and examine all joints as well as brand-new pipework for leaks and also tighten them if essential. Fill up the tub and additionally examine the overflow outlet and the regular electrical outlet for leaks.
Finally, fix the bathroom paneling as explained in the producer's instruction manual. Tiling and also securing around the bathtub needs to wait till the tub has been made use of a minimum of when as this will resolve it into its last setting.
Fitting New Touches
If the tails of the brand-new taps are plastic, after that you will need a plastic adapter to avoid damage to the string. One end of the connector fits on the plastic tail of the faucet as well as the other end gives a connection to the existent supply pipelines.
If you need to fit a monobloc, then you will call for decreasing couplers, which attaches the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next off, position the tap in the installing hole in the bath/basin making certain that the washers are in place in between the faucet as well as the sink. Secure the faucet in place with the producer given backnut. Once the faucet is firmly in place, the supply pipelines can be attached to the tails of the taps. The taps can either be attached by using corrugated copper piping or with regular faucet connectors. The previous kind ought to be linked to the faucet ends initially, tightening up just by hand. The supply pipes can later on be attached to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Bath tub
In the area where the bathroom fulfills the tile, it is required to secure the accompanies a silicone rubber caulking. This is important as the installation can move enough to fracture a rigid seal, triggering the water to pass through the wall surface between the bath as well as the tiling, bring about complications with dampness as well as feasible leakages to the ceiling listed below.
You can pick from a variety of coloured sealants to blend in your components and installations. They are marketed in tubes and cartridges, as well as can securing voids approximately a width of 3mm (1/8 inch). If you have a larger space to load, you can fill it with twists of drenched paper or soft rope. Remember to always fill up the bath tub with water prior to securing, to allow for the motion experienced when the bathtub remains in usage. The sealant can crack fairly early if you do not think about this movement prior to sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise easily offered on the marketplace. It is suggested to fit the tiles utilizing water-resistant or water-proof glue and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you like more info about Tools You Need to Install a New Bathtub ? Write a remark further down. We'd be pleased to hear your thinking about this entry. Hoping that you come back again later on. If you enjoyed our blog entry please make sure you remember to pass it around. Thank you so much for your time invested reading it.
Get Offer Report this page